Enabling Prepaid Service

Descriptions

The UltraWAVE Prepaid System (PPS) is a full featured Intelligent Network (IN) prepaid system. As an IN Service Control Point (SCP), the PPS functions with the UltraWAVE system to provide a turnkey and complete solution for mobile prepaid service. With prepaid telephony, subscribers pay before they use the service. Subscribers buy a certain amount of service by prepaying a certain amount of money, and can use the service up to the amount purchased. Once that amount is used, subscribers have to prepay again to continue using the service. Refer to PPS User Manual for more information.

Implementation

1.Click the Advanced main menu.

2.Select HLR under the Subscriber submenu.

3.Find the IMSI of the subscriber want to activate prepaid service, click it to display the subscriber parameter window.

4.Check the required toggle boxes of the following parameters and enter the proper values.

5.Click the button at the top of the parameter table to upload the new values to HLR servers.

No.	Parameter	Explanation
43	CAMEL Flag	Check CAMEL toggle boxes to activate prepaid service. Support CAMEL is a total flag of CAMEL provisioning. To enable any CAMEL service, select the toggle boxes: •O-CSI: Originating CAMEL subscription information •T-CSI: Terminating CAMEL subscription information •SS-CSI: Supplementary service notification CAMEL subscription information •SMS-CSI: Short message service notification CAMEL subscription information •GPRS-CSI: GPRS notification CAMEL subscription information
44*	O-CSI	Define the originating CAMEL Subscription Information
45*	T-CSI	Define the terminating CAMEL Subscription Information
46*	SS-CSI	Define the supplementary service notification CAMEL Subscription Information
47*	SMS-CSI	Define the short message service notification CAMEL Subscription Information
48*	GPRS-CSI	Define the GPRS notification CAMEL Subscription Information

O-CSI Parameter	Descriptions
Detect Point Value	Trigger detection point. The DP List indicates on which detection point triggering shall take place. CAMEL Phase2: DP2. CAMEL Phase 3: DP2, DP4. •Default =2
Service Key	The service key identifies to the SCF the service logic that should apply. •Default = 0
SCF Number	SCF E.164 number. •Format = 91+CC+NDC+SN
Default Call Handling	Indicate whether the call shall be released or continued as requested in case of error in the SSF to SCF dialogue. •Default = Continue Call
Match Type Flag	These parameters should be left at their default values.
Match Type
Destination Number List Flag
Destination Number x
Destination Number Length Flag
Destination Number Length x
Call Type Flag
Call Type
Default Capability Handling	CAMEL Capability Handling indicates the phase of CAMEL which is asked by the SCF for the service. •Default = 2

T/SMS/GPRS-CSI Parameter	Descriptions
Detect Point Value	Trigger detection point. The TDP List indicates on which detection point triggering shall take place. CAMEL Phase2: DP2; CAMEL Phase 3: DP2, DP4. •Default =2
Service Key	The service key identifies to the SCF the service logic that should apply. •Default = 0
SCF Number	SCF E.164 number. •Format = 91+CC+NDC+SN
Default Call Handling	Indicate whether the call shall be released or continued as requested in case of error in the SSF to SCF dialogue. •Default = Continue Call
Default Capability Handling	CAMEL Capability Handling indicates the phase of CAMEL which is asked by the SCF for the service. •Default = 2

SS-CSI Parameter

Descriptions

Event x

This parameter should be left at their default value.

SCF Number

SCF E.164 number.

•Format = 91+CC+NDC+SN

1.Go to EMS >Configuration >NSS >SCCP.

2.Make sure the System ID at the upper right corner displays SCCP(MSS_Pub), click the button.

3.Click the Local Node tab.

The SRF local node is used for the prepaid services related with announcement prompt.

1.Click the hyperlinked index number of SRF-0 to open its Option window.

2.Configure the relevant parameters given in the following table.

3.Click the button to update parameters to application servers.

4.Click the upper Local Node hyperlink to go back to the previous window.

Sub-parameter	Description (Click highlight SAVE after change)	Recommended Value
Network Indicator	Specify the local node to a network. Choose the same network as MTP3 setting.	National
E.164 Number	The E.164 node address of SRF-0.	SRF-0 E.164 Number
IP 0	IP address of MSS 0.	IP of MSS-0
IP 1	Reserved as 255.255.255.255.	255.255.255.255

The SRF local node is used for the prepaid services related with announcement prompt.

1.Click the hyperlinked index number of SRF-1 to open its Option window.

2.Configure the relevant parameters given in the following table.

3.Click the button to update parameters to application servers.

4.Click the upper Local Node hyperlink to go back to the previous window.

Sub-parameter	Description (Click highlight SAVE after change)	Recommended Value
Network Indicator	Specify the local node to a network. Choose the same network as MTP3 setting.	National
E.164 Number	The E.164 node address of SRF-1.	SRF-1 E1.64 Number
IP 0	IP address of MSS 1.	IP of MSS-1
IP 1	Reserved as 255.255.255.255.	255.255.255.255

1.Click the hyperlinked index number of SSF to open its Option window.

2.Configure the relevant parameters given in the following table.

3.Click the button to update parameters to application servers.

4.Click the upper Local Node hyperlink to go back to the previous window.

Sub-parameter	Description (Click highlight SAVE after change)	Recommended Value
Network Indicator	Specify the local node to a network. Choose the same network as MTP3 setting.	National
E.164 Number	The E.164 node address of SSF.	SSF E.164 Number
IP 0	IP address of MSS 0.	IP of MSS-0
IP 1	IP address of MSS 1.	IP of MSS-1

1.Click the hyperlinked index number of SCF-CAP to open its Option window.

2.Configure the relevant parameters given in the following table.

3.Click the button to update parameters to application servers.

4.Click the upper Local Node hyperlink to go back to the previous window.

Sub-parameter	Description (Click highlight SAVE after change)	Recommended Value
Network Indicator	Specify the local node to a network. Choose the same network as MTP3 setting.	National
E.164 Number	The E.164 node address of SCF-CAP.	SCF-CAP E.164 Number
IP 0	IP address of MSS 0.	IP of MSS-0
IP 1	IP address of MSS 1.	IP of MSS-1

The SCP-MAP local node is used for the prepaid services related with USSD.

1.Click the hyperlinked index number of SCF-MAP to open its Option window.

2.Configure the relevant parameters given in the following table.

3.Click the button to update parameters to application servers.

4.Click the upper Local Node hyperlink to go back to the previous window.

Sub-parameter	Description (Click highlight SAVE after change)	Recommended Value
Network Indicator	Specify the local node to a network. Choose the same network as MTP3 setting.	National
E.164 Number	The E.164 node address of SCF-MAP.	SCF-MAP E.164 Number
IP 0	IP address of MSS 0.	IP of MSS-0
IP 1	IP address of MSS 1.	IP of MSS-1

The SMPP-EMSE local node is used for the prepaid services related with notification short message.

1.Click the hyperlinked index number of SMPP-EMSE to open its Option window.

2.Configure the relevant parameters given in the following table.

3.Click the button to update parameters to application servers.

4.Click the upper Local Node hyperlink to go back to the previous window.

Sub-parameter	Description (Click highlight SAVE after change)	Recommended Value
Network Indicator	Specify the local node to a network. Choose the same network as MTP3 setting.	National
E.164 Number	The E.164 node address of SMPP-EMSE.	SMPP-EMSE E.164 Number
IP 0	IP address of MSS 0.	IP of MSS-0
IP 1	IP address of MSS 1.	IP of MSS-1

The SMPP-SMSC local node is used for the prepaid services related with notification short message.

1.Click the hyperlinked index number of SMPP-SMSC to open its Option window.

2.Configure the relevant parameters given in the following table.

3.Click the button to update parameters to application servers.

4.Click the upper Local Node hyperlink to go back to the previous window.

Sub-parameter	Description (Click highlight SAVE after change)	Recommended Value
Network Indicator	Specify the local node to a network. Choose the same network as MTP3 setting.	National
E.164 Number	The E.164 node address of SMPP-SMSC.	SMPP-SMSC E.164 Number
IP 0	IP address of MSS 0.	IP of MSS-0
IP 1	IP address of MSS 1.	IP of MSS-1

1.Go to EMS >Configuration >NSS >PPS.

2.Click the button at the upper right corner.

1.On the System Control tab, refer to the PPS parameters dictionary to configure the relevant parameters.

2.Click the button to update parameters to application servers.

1.Go to EMS >Configuration >NSS >PPS.

2.Click the button at the upper right corner.

1.Click the SRF Parameters tab, refer to the PPS parameters dictionary to configure the relevant parameters.

2.Click the button to update parameters to application servers.

A Class of Service (COS) is the basic entity used to define prepaid service packages, and constitutes a major part of the service data. Most of the service behavior, including the tariff structure, allowed dialed numbers, the number of phone book entries allowed for a subscriber in the Friends and Family feature and many other service characteristics such as the switch of Close User Group and Friend and Family, are defined as part of the COS.

Each subscriber is assigned to only one COS. The subscriber COS name is listed in the subscriber record and is read whenever the service processes the subscriber.

Overall, the behavior of the service for a given subscriber is determined by the subscriber's COS. Only a few personal configuration attributes (such as the subscriber's default language) are kept in the subscriber records; the rest are defined in the subscriber COS and are shared by all the subscribers assigned to that COS.

A total of 64 COS can be defined in the system, allowing the prepaid service to offer multiple service packages to subscribers.

1.Go to EMS >Configuration >NSS >PPS.

2.Click the button at the upper right corner.

1.Click the COS tab, refer to the PPS parameters dictionary to configure the relevant parameters.

2.Click the button to update parameters to application servers.